![]() ![]() Sensitization: No sensitizing effects known. Skin irritation or corrosion: Causes skin irritation.Įye irritation or corrosion: Causes serious eye irritation. LD/LC50 values that are relevant for classification: No data Hazardous decomposition products: Carbon monoxide and carbon dioxide Possibility of hazardous reactions Reacts with strong oxidizing agents Thermal decomposition / conditions to be avoided: Decomposition will not occur if used and stored according to specifications. Partition coefficient (n-octanol/water): No data available.Ĭhemical stability Stable under recommended storage conditions. Sublimation temperature / start: No data availableįlammability (solid, gas) Highly flammable.ĭecomposition temperature: No data availableĭensity at 20 ☌ (68 ☏): 1.7 g/cm 3 (14.187 lbs/gal) Melting point/Melting range: 500-600 ☌ (932-1112 ☏) (subl)īoiling point/Boiling range: No data available ![]() Information on basic physical and chemical properties Penetration time of glove material (in minutes) 480īody protection: Protective work clothing. Quality will vary from manufacturer to manufacturer. The selection of suitable gloves not only depends on the material, but also on quality. Only use equipment tested and approved under appropriate government standards. Risk assessment should be performed to determine if airpurifying Use a respirator with type N95 (USA) or PE (EN 143) cartridges as a backup to engineering controls. Recommended filter device for short term use: Maintain an ergonomically appropriate working environment.īreathing equipment: Use suitable respirator when high concentrations are present. Wash hands before breaks and at the end of work. Remove all soiled and contaminated clothing immediately. Keep away from foodstuffs, beverages and feed. Properly operating chemical fume hood designed for hazardous chemicals and having an average face velocity of at least 100 feet per minute.Ĭomponents with limit values that require monitoring at the workplace:įollow typical protective and hygienic practices for handling chemicals. EXPOSURE CONTROLS/PERSONAL PROTECTIONĪdditional information about design of technical systems: Store in cool, dry conditions in well-sealed containers. Information about storage in one common storage facility: Store away from oxidizing agents.įurther information about storage conditions: Requirements to be met by storerooms and receptacles: Store in a cool location. Information about protection against explosions and fires: Protect against electrostatic charges.Ĭonditions for safe storage, including any incompatibilities Store in cool, dry place in tightly closed containers.Įnsure good ventilation at the workplace. See Section 8 for information on personal protection equipment. See Section 7 for information on safe handling Prevention of secondary hazards: Keep away from ignition sources. Methods and materials for containment and cleanup: Keep unprotected persons away.Įnvironmental precautions: Do not allow material to be released to the environment without official permits. Personal precautions, protective equipment and emergency procedures If this product is involved in a fire, the following can be released: Special hazards arising from the substance or mixture Fight larger fires with water spray or alcohol resistant foam. Suitable extinguishing agents Carbon dioxide, extinguishing powder or water spray. Indication of any immediate medical attention and special treatment needed: Most important symptoms and effects, both acute and delayed: Rinse opened eye for several minutes under running water. Immediately wash with soap and water rinse thoroughly. If not breathing, provide artificial respiration. (Hazardous Materials Identification System) P501 Dispose of contents/container in accordance with local/regional/national/international regulations.ĭ2B - Toxic material causing other toxic effects Remove contact lenses, if present and easy to do. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. P280 Wear protective gloves/protective clothing/eye protection/face protection. P261 Avoid breathing dust/fume/gas/mist/vapors/spray. P210 Keep away from heat/sparks/open flames/hot surfaces. Thin Film Deposition & Evaporation Materials.Additive Manufacturing & 3D Printing Materials. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |